Coating & Protective Systems in Mumbai
Liquid-applied protective and decorative systems that form a continuous barrier over concrete, masonry and steel. Atlanta Waterproofing & Protective System carries 6 systems in this category, selected by substrate, exposure and traffic rather than by habit. Each page below states when the system is right and when it is the wrong answer.
6 systems in this category
Chemical Coating
Chemical coating is the application of a liquid chemical-based protective barrier to concrete or masonry, forming a continuous film that resists water penetration and chemical attack. Product selection is driven by the exposure it must survive rather than by appearance..
IS 3067
Cement Based Coating
Cement-based coating is a polymer-modified cementitious slurry applied to concrete and masonry to form a rigid, breathable water-resistant layer. Because it is cementitious it bonds well to damp substrates and to concrete, which makes it the common choice for tanks, wet areas and internal tanking..
IS 2645 · IS 3067
Elastomeric Coating
Elastomeric coating is a high-build flexible coating that stretches to bridge hairline cracks as a structure moves and temperature cycles. It is the standard external facade and terrace coating where fine cracking is expected, because a rigid paint over a live crack simply splits again..
IS 3067
Acrylic Coating
Acrylic coating is a water-based protective and decorative coating offering good UV stability and colour retention with moderate flexibility. It is widely used as an external finish coat over prepared and primed masonry where appearance matters alongside weather protection..
IS 3067
Solvent Based Coating
Solvent-based coating uses organic solvents as the carrier, producing a hard, dense, chemically resistant film with strong adhesion and good performance in demanding industrial exposures. It requires proper ventilation and trained handling during application..
IS 3067
Food Grade Coating for Water Bodies
Food-grade coating is a non-toxic lining certified as safe for contact with potable water, used inside drinking-water tanks and reservoirs. The certification is the point: a general-purpose waterproofing coating inside a drinking-water tank is a health hazard regardless of how well it performs technically..
IS 3067
The rest of what we do
- SEC. 02 / TRADITIONALTraditional & Specialised Waterproofing
Time-proven Indian terrace systems and high-performance specialist linings, from brick bat coba to polyurea.
- SEC. 03 / MEMBRANEMembrane Waterproofing Systems
Sheet-applied barriers — torch-on bitumen, heat-welded thermoplastic and pre-applied HDPE for below-grade work.
- SEC. 04 / AREAArea-Specific Waterproofing
System selection driven by where the water is: terrace, basement, wet area, tank, podium, lift pit, pool.
- SEC. 05 / GROUTINGLeakage Treatment & Grouting
Remedial injection and joint treatment that stops water already moving through a structure.
- SEC. 06 / FINISHINGFlooring & Finishing
Wearing surfaces and screeds that protect the waterproofing layer beneath and take the traffic.
- SEC. 07 / RESTORATIONStructural & Restoration Works
Concrete repair, structural strengthening and facade renewal for ageing and distressed buildings.
Frequently asked
How do I choose between the systems in coating & protective systems?
Selection is driven by the substrate, the exposure, the traffic the surface will take, and whether the structure moves. Each system page below states plainly when that system is the right choice and — more usefully — when it is not. If you are unsure, a site inspection settles it in one visit.
Can these systems be combined?
Frequently, yes. Most real buildings need more than one: a terrace system with grouting to stop an active crack first, or a facade coating over repaired plaster. What matters is that the systems are chemically and mechanically compatible with each other and with the substrate.
Do you supply materials, or only apply them?
We supply and apply as a single scope, so responsibility for both material selection and workmanship sits in one place. Where a project specification names a particular manufacturer or product, we work to that specification.
Book the inspection. It costs nothing and it settles the argument.
An engineer visits, finds the actual source, and tells you what the building needs and why. You get a clear scope before any money is discussed.
Mon–Fri 08:00–18:00 · Sat 09:00–16:00 · Jogeshwari West